Clean Your Gutters

On average, gutters accumulate anywhere from 40-250 pounds of debris per year! This buildup can create all kinds of problems for your home such as foundation erosion, mosquito infestations and damage to your roof and gutter system, which can cost thousands of dollars to replace.

1. Remove all debris from your gutters. Get every leaf and twig with a gloved hand. Go section-by-section, dump the debris you can reach in a bucket, and then move the ladder down (very carefully).

2. Check for damages. After removing debris, check for corrosion and any holes or dents. Tip: If you find small holes, place a piece of painter’s tape by the hole so you can easily find it when you’re ready to repair. If you’ve found small holes in your gutter, you can seal them with clear silicone sealant.

3. Test the drainage. Gently run water through your gutter with a garden hose to ensure your gutter is draining correctly. If water is standing still, increase the grade of your gutter to create and maintain a proper drain slope. To do this, simply bend the hangers. The gutter should slope at least 1/4-inch for every 5-10-feet of gutter.

4. Check for sagging. A sagging gutter is a useless gutter. Rainwater will get trapped in the sagging portion and become stagnant mess (a love nest for mosquitoes). If the gutters are sagging, it’s likely because the nails holding the gutters have loosened. Try to hammer them back into place. If the nails won't hold, replace them with screws.

5. Unclog your downspouts. If the downspout is clogged, work to loosen the debris from the bottom up to avoid further clogging the downspout. Turn your water hose on high and run it up the spout from the bottom. If this doesn’t work, try a plumber’s snake (again, from the bottom to the top). If all else fails, remove the downspout and tackle the clog by hand.

If you think you have any issues that need to be inspected further then call us to help, We can inspect your roof or attic and provide you with a detailed report. We can recommend the next steps for you to take.

Comments

Clearing the Air: Indoor Air Quality Concerns After Water and Fire Damage

When a home or business experiences water or fire damage, the immediate focus is often on the visible destruction. Charred walls, soaked carpets, and ruined possessions dominate our attention. However, a significant but less obvious concern is the impact these events have on indoor air quality (IAQ). Addressing these concerns is crucial for health, safety, and a successful restoration process. The Unseen Dangers: Indoor Air Contaminants 1. Mold and Mildew Water damage, whether from floods, burst pipes, or firefighting efforts, creates a perfect breeding ground for mold and mildew. These fungi thrive in damp, warm environments and can start growing within 24-48 hours after water exposure. Mold spores are airborne and can cause respiratory issues, allergic reactions, and other health problems, especially for those with preexisting conditions like asthma. 2. Smoke and Soot Fire damage leaves behind more than just ashes. Smoke and soot particles can infiltrate your HVAC system, carp...

Common places for moisture - in the Attic, Basement and Crawl space

Moisture is a pervasive problem that can wreak havoc on your home if not addressed promptly. It can lead to structural damage, mold growth, and a host of health issues. Three of the most common areas where moisture problems often arise are the attic, basement, and crawl space. Understanding the causes and solutions for moisture in these areas can help you maintain a healthy and safe home environment. The Attic Causes of Moisture in the Attic Roof Leaks: One of the most common causes of moisture in the attic is a leaky roof. Damaged shingles, flashing, or vents can allow water to seep in during rainstorms. Poor Ventilation: Attics require proper ventilation to expel warm, moist air. Without adequate ventilation, moisture can accumulate, especially in colder months when warm air from the living space rises. Improper Insulation: Insufficient or improperly installed insulation can lead to condensation. When warm air from the house meets the cold surfaces of the attic, it can create mois...

Is there a difference between Mold and Mildew?

With water damage claims on the rise, we hear a lot of talk these days about the dangers of mold. Within 24 to 48 hours of water damage, mildew and mold can start growing on wood products, tiles, drywall, carpets, fabrics and other organic materials. Even worse, it will continue to grow until steps are taken to eliminate the source of moisture, and effectively deal with the problem. So what is the difference between mold and mildew? Plain and simple, mildew and mold are both fungi. Fungi can live in many different types of environments such as in soil, on vegetation, and on surfaces exposed to moist conditions like a wall or ceiling after flood damage. Fungi reproduce by spores and can spread quickly. What is Mildew? Mildew is mold in its early stage and often the term is used interchangeably with the word mold. That whitish-gray, powdery substance sometimes seen on the leaves of a plant is mildew. Mildew is a surface fungi that grows on organic material li...

Search This Blog